Live identification power failure identification
Flexible coil transient tracking
Color icon dynamic indication
Current range: 0-5000A
Pulse current: 5A Max
Pulse voltage: 500V
Pulse width: 2mS
Compound frequency: 625Hz,1562 Hz
Medium and high frequency: 2500Hz,10kHz
Voltage range: 0-600V
| Model number | UT263B (Transmitter Specification) |
|
Model number | UT263B (Transmitter Specification) |
| Work energy | Emit compound pulse frequency current signal, disy battery voltage, dynamic indication of emission state | Test line length | 3 meters with alligator clip, 1 each red and black | |
| Electricity source | 11.1V large capacity rechargeable lithium battery, fully charged continuous operation for about 8 hours | Transmitting clamp wire length | Three meters | |
| Disy mode | Large LCD disys the remaining battery voltage in real time, with backlight | LCD size | Length and width 128mm×75mm; Disy domain 124mm x 67mm | |
| Transmission frequency | 625Hz、1562Hz、2500Hz、10KHz（带电识别时）,按上下箭头键调节Transmission frequency | Size of outer packing | Length width height 400mm×245mm×335mm | |
| Pulse voltage | 500V (power failure identification) | Operating temperature | -10℃～40℃ | |
| Pulse current | Max 5A (depending on the size of the loop resistance) | Storage condition | -20℃~50℃,≤ 95% RH, no condensation | |
| Pulse frequency | 1 time/second | Backlight control | Yes, white backlight | |
| Pulse width | 2ms | Battery power | When the battery low arrives at 9.65V, the battery low icon is disyed, indicating
Charge the battery; Below 9.5V, the device automatically shuts down |
|
| Output mode | When charged identification caliper coupling; Power failure identification when direct output | Charging device | 12.6V DC charger | |
| Firing clamp inner diameter | φ125mm | Charging interface | 圆形Charging interface,DC 标识 | |
| Ground pin dimensions | Length width and thickness 225mm×100mm×10mm | Pressure resistance | -A device is designed in an integrated manner and a tool box. The box can bear about
200kg pressure |
|
| Transmitter size | 320mm×275mm×145mm | Pressure resistance | AC 3700V/rms(top surface of instrument case not before bottom surface) | |
| Launch clamp size | Length width 300mm×175mm×50mm | Electromagnetic properties | IEC61326(EMC) | |
| Size of outer packing | Length width height 400mm×245mm×335mm | Charging device | 12.6V DC charger | |
| Instrument quality | Transmitter 2.5kg, transmitter clamp: 1.08kg, total mass: 4.4kg (including receiver) | Refer to safety rules | CAT Ⅲ 300V,CAT IV 150V, pollution level 2 |
| Model number | UT263B (Receiver Specification) |
|
Model number | UT263B (Receiver Specification) |
| Work energy | 识别并解码Pulse current信号,交流电压、电流、频率测量 | Direction recognition | Yes, the transmitting clamp, the receiving clamp does not load the signal must be in the same direction for the identification
One of the conditions of success |
|
| Electricity source | 7.4V large capacity rechargeable lithium battery fully charged continuous operation of about 6 hours | |||
| Cable identification is successful | The green checkmark indicates (√) | |||
| Disy mode | 3.5 "true color LCD disy, color icon indication | Non-target cable | Red - orange cross icon indicates (×) | |
| Detection range | 停电识别：线圈可检测回路电阻为0Ω～10kΩ的脉冲信号;检测回路电 阻为10kΩ 时,需保证发射机Battery power为11V以上 | Signal calibration | Yes, calibrate the transmitting signal. The percentage of current that receives a signal but does not transmit it
Between 75percent and 135percent of the calibration value is one of the conditions for recognition success |
|
| 带电识别：线圈可检测回路电阻为0Ω～200Ω的脉冲信号;检测回路电阻为200Ω 时,需保证发射机Battery power为11V以上 | After calibration can not change the test frequency and amplification, otherwise to re - mark
Determine; Testing different cables requires re-calibration |
|||
| Range/accuracy | Ac voltage: 0.01V ~ 600V(50Hz/60Hz)/±2percent±1dgt | Inside diameter of coil | Sorta can be customized for further reason | |
| Ac current: 0.01A ~ 5000A(50Hz/60Hz)/ ±2percent±1dgt | Lead length | Flexible current pliersLead length：2m | ||
| Current frequency: 45Hz~70Hz/±2percent±1dgt | Voltage test line | 1m long (1 red and 1 black) | ||
| Flexible current pliers | At length of 630mm, sor6 mm or 12.5mm | Identification signal | Color signal amplitude and digital disy | |
| Receiver size | Length width and thickness 207mm×101mm×45mm | Detection rate | About 1 times/second | |
| Charging device | 9V DC charger | Gain control | Under the test interface, press the left and right arrow keys to adjust signal amplification, signal amplitude
The degree bar is best at 10~100 |
|
| Rated current | About 300mA max | Backlight control | Press the up and down arrow keys to adjust the LCD back -- in the startup function selection screen
The brightness of light |
|
| Working temperature and humidity | -10℃ ~ 40℃; 80percentRh below | Automatic shutdown | 开机约 30 分钟后,仪表Automatic shutdown,以降低电池消耗 | |
| Storage temperature and humidity | -10℃~50℃,≤ 95% RH, no condensation | Battery voltage | 当Battery voltage低亍 6.5V 时,Battery voltage低图标显示,提醒
Charge the battery |
|
| Receiver quality | 接收机：370g(带电池),Flexible current pliers：172g | Charging interface | USB Charging interface | |
| Withstand voltage | AC2000V/rms(Before the front and rear ends of the housing) | Suitable for safety rules | CAT Ⅲ 600V Pollution Level 2 |
